Home > Products > Gas Forced Induction Water Methanol Kits > Stage 1 Boost Cooler™ >

Stage 1 Boost Cooler™ (Nylon Line)

Snow Performance Stage 1 Boost Cooler Water-Methanol Injection Kit


 
Alternative Views:


FREE SHIPPING On Orders Over $99!
Our Price $359.99


Product SKU: SNO-201


Choose Line Color:


Choose Nozzle Size:


Quantity:  
Features Contents Instructions | Nozzle Selection Guide
 
Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged) and uses a adjustable boost switch to inject a fixed amount of water methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost set ups, drag race applications, and vehicles with a positive displacement supercharger (Roots/Twinscrew) looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user chosen switch, such as a full throttle switch, nitrous switch, etc.

This kit utilizes the only OEM approved water methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO Pump is designed to be in the elements with O-Ring connections that are then sealed and potted at our Colorado facility to ensure no moisture can enter the pump internals. Compare this to pumps that us a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat to greatly decrease pump life. The Stage 1 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL™ compression fittings for guaranteed leak free operation even when using 100% methanol. For a extremely robust, reliable water methanol injection experience that won't brake the bank look no further than the Snow Performance Stage 1 Boost Cooler!

Features:
  • U.S.A. Made
  • Adjustable Water Methanol Engagement & Monitoring
  • Recommended For High HP, Drag Race, and Positive Displacement Supercharger Applications
  • Supports 1,000+ HP
  • 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
  • Snow Performance Hyper-Sonic Water Methanol Nozzle
  • Snow Performance ACU-SEALWater Methanol Compression Fittings
  • Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump
  • Snow Performance Running "S" Engraved Low Profile Nozzle Holder
  • Snow Performance Running "S" Engraved Low Profile High Flow Check Valve

Average Rating: 5 of 5 Total Reviews: 2 Write a review »

  0 of 0 people found the following review helpful:
 
Get ride of that knock February 26, 2018
Reviewer: Bill Knutsen from Denver, CO United States  
Completely eliminated engine knock I was experiencing. A very cheap effective way to gain some added insurance on a very expensive motor. Victor over the phone was especially helpful getting me dialed in with what kit to use and what size nozzle to run. Would definitely recommend.

Was this review helpful to you?

  2 of 2 people found the following review helpful:
 
2005 Mustang GT Procharged December 17, 2015
Reviewer: Adam  
This thing is the bomb! Increased boost to 15 PSI and dropped my air charge from 180 degrees to 120 degrees on the dyno after doing two pulls!

I was not sure wither to go with the Stage 2 or 1 but for reducing IATs this thing works great!

Was this review helpful to you?