"The Snow Boost Cooler added a tad over 100 hp and a huge jump in torque." - Diesel Builder, June 2007
Categories
 
 

Viewing products in PT Cruiser Turbo

 
 
 
Stage 2 Boost Cooler™

Stage 2 Boost Cooler™

This kit uses manifold boost pressure to determine when and how much water methanol to inject. Proportionally injecting according to boost pressure gives accurate delivery of water-methanol and allows the most cooling and performance improvement over a wide range. More power and driveability is the result. It can be used on any forced induction engine: carbureted, fuel injected, turbocharged, positive displacement or centrifugal blowers. The most suitable are the centrifugal supercharged and turbocharged engines, as they build boost is a more progressive manner concerning water-methanol injection. The positive displacement blower engines will work, but it might take a bit more work to dial in the delivery. For higher boost applications (over 25psi), the controller can be upgraded to our VC100 unit.
Continue
 
 
SafeInjection™

SafeInjection™

The ultimate safeguard for your engine. SafeInjection® is a watchdog that always monitors the system output flow. Designed as an add on to the Boost Cooler® water/methanol injection system, SafeInjection® provides for a safe tune in those instances where no injection is present and an aggressive tune is utilized. This system can reduce boost and/or timing anytime injection quantity goes below the set point regardless of the reason (ran out of fluid, clogged line, etc.). It does this with the upgrades listed below. This sets your vehicle into a "safe mode" making your tune instantly conservative for the ultimate in safe water/methanol injection. Even without the upgrades, the system features an LED light that will warn the driver in a low-flow situation.
Continue
 
 

SafeInjection® Gauge

New gauge indicates actual flow rate of water-methanol injection system for easy tuning and peace of mind. Replaces prior digital only design.
Continue
 
 
SafeInjection™ Wastegate Solenoid

SafeInjection™ Wastegate Solenoid

Solenoid such that boost is reduced in a wastegated turbo set-up. This is to be used in conjunction with the SafeInjection module p/n 30020.
Continue
 
 
2.5 Gallon Reservoir

2.5 Gallon Reservoir Upgrade

The new 2.5 Gallon Reservoir gives much more range than the included 3 qt tanks, and is fairly small in size – 13”l x 9.5”h x 7.5”w (similar to a very small car battery) and includes an additional 15 feet of tubing all fittings required, and an anti gravity feed solenoid.
Continue
 
 
Nitro Booster™

Nitro Booster™

Nitro Booster™ is a great power adder designed for use with gasoline engines using Boost Cooler™ water methanol injection kits. A proprietary blend of nitromethane and a specially developed emulsifier that keeps Nitro Booster™ equally distributed in the water-methanol mixture. This allows for a small percentage of nitromethane to be injected into the engine in the correct proportion with air and fuel to produce impressive increases in power - Typically, 50hp on a 500 hp vehicle. Nitromethane has fewer BTUs than gasoline, but contains oxygen and acts like a chemical supercharger and an octane enhancer to safely increase power.
Continue
 
 
Stage 3 Gasoline Boost Cooler®

Stage 3 Gasoline Boost Cooler®

The Stage 3 Boost Cooler® is unmatched for accuracy and adjustability in water-methanol injection systems. This system can be used on any forced induction engine, or ANY engine with a traditonal EFI system, and features our green LCD display with on-the-fly adjustability.
Continue
 
 
Stage 3 Gasoline MPG MAX® Boost Cooler®

Stage 3 Gasoline MPG MAX® Boost Cooler®

The MPG MAX® Stage 3 Boost Cooler® is unmatched for increases in Fuel Economy AND Power in water-methanol injection systems. Key to this is accuracy and adjustability designed into the system through the standalone LCD controller. This Boost Cooler® can be used on any forced induction engine, or ANY engine that has a traditonal EFI system.
Continue
 
 
Stage 3 Gasoline Boost Cooler™  Upgrade

Stage 3 Gasoline Boost Cooler™ Upgrade

Already have a Snow Performance Stage 2 gasoline Boost Cooler™? Snow Performance offers you the option to upgrade just the controller to make your Stage 2 system into a Stage 3.
Continue
 
 
Stage 1 Boost Cooler™

Stage 1 Boost Cooler™

The gasoline Stage 1 Boost Cooler™ kit is available for forced induction applications that are either fuel injected or carbureted. Operation is very simple: the system starts injecting when the boost switch reaches the user-adjustable point and it injects a fixed amount of fluid through the nozzle until the switch opens again. This makes it a good choice for low to medium boost setups looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, etc.
Continue
 
 
Boost Juice

Boost Juice™

Boost Juice™ is Snow Performance’s proprietary mix of 49% methanol and 51% purified water. It is made in a controlled environment with special care to make sure the ratios are accurate to result in a high performance water methanol fluid formulated for use in the Boost Cooler™ injection system.
Continue