Home > Water-Methanol Accessories

All Snow Performance award winning water-methanol injection accessories can be found here. From pumps to reservoirs to pre-mixed water-methanol fluid Snow Performance has what you need to improve your water injection system. Don't see what you are looking for? Chances are we have it! To inquire about a water-methanol product shoot us a email at sales@snowperformance.net.






Water-Methanol Failsafe/Flow Gauge Water-Methanol Injection Controllers Water-Methanol Reservoirs

When you want to push the limit with your water-methanol injection system you need a bulletproof fail-safe that will intervene if water-methanol flow is stopped or interrupted. Introducing the Safe injection (US Patent# 20070144485A1) water-methanol failsafes.

The Safe Injection monitors flow when ever the system is active. If flow goes below a user set point the Safe Injection will trigger a 3-way solenoid to cut boost or tie directly in to a aftermarket ECU with a timing retard switch to cut timing. This way you can run a very aggressive tune with 100% safety!

The optional methanol flow gauge can tie directly into the Safe Injection and read real time flow through the system showing you exactly what's happening. Very useful for race applications that depend on water-methanol for their tune!

Have questions about the Safe injection unit, supercharger bypass valve kit & more? We want to hear it! Shoot us a email at sales@snowperformance.net.





Snow Performance water-methanol controllers are manufactured right here in the U.S.A and can control injection off different variables in a gas/diesel engine. Below is a breakdown of the water meth injection controllers and what variable they operate off of.

Pressure Switch- Turns pump on/off once a certain boost pressure is reached. Adjustable from 1-15 PSI. Recommended for low boost set ups.

VC-20- Fully adjustable variable controller that will progressively command injection between two boost points (start & full). For example, if the start point is set to 5 PSI and the full set to 10 PSI the controller will begin injection at 5 PSI and progressively increase injection volume with boost until it reaches the max injection point of 10 PSI. Fully adjustable between 1-20 PSI. Recommended for all forced induction applications.

VC-50- Fully adjustable variable controller that will progressively command injection between two boost points (start & full). For example, if the start point is set to 5 PSI and the full set to 20 PSI the controller will begin injection at 5 PSI and progressively increase injection volume with boost until it reaches the max injection point of 20 PSI. Fully adjustable between 1-50 PSI and comes with heads up boost gauge/water-methanol controller display. Recommended for all forced induction application.

MAFU (GAS ONLY)- Fully adjustable variable controller that will progressively command injection between two points on the mass air flow (MAF) or manifold absolute pressure sensor (MAP) . For example, if you have a 0-5V MAF sensor and the start point is set to 2.5 volts and the full set to 5 volts the controller will engage injection at 2.5 volts and progressively increase injection volume with the MAF reading until it reaches the maximum injection point of 5 volts. Fully adjustable between 0-5V and all frequency readings. Recommended for all N/A vehicles with a MAF/MAP sensor and EFI vehicles with a positive displacement supercharger.

MCVC (GAS ONLY)- Fully adjustable variable controller that will command injection off of engine RPM and vacuum. Once the vehicle reaches a adjustable RPM point the controller will begin progressively injecting water-methanol based off of engine vacuum. Recommended for all N/A carbureted vehicles.

Stage 3 Controller (GAS ONLY)- Fully adjustable variable controller that will progressively command injection based off of boost & fuel injector pulse witch (EFI) or fuel pressure sensor voltage (DI). Start and full points are adjustable to match what the vehicle is making. Recommended for all forced induction applications.

MPG-MAX (DIESEL ONLY)- Fully adjustable variable controller that will progressive command injection based off of boost & EGTs. Start & full points are adjustable to match what the vehicle is making. Recommended for all turbo diesel applications where EGTs are a problem.

Have a question on which controller is best for your application? Email us at sales@snowperformance.net.



Snow Performance water-methanol injection tanks are a great addition to your water-methanol system to move the supply of fluid into the trunk or the bed of the vehicle. All reservoir upgrades & racing fuel cells come with the necessary brackets, solenoids, tubing, and fittings to completely install your Snow Performance upgrade in the desired location. Our water-methanol injection reservoirs & racing fuel cell kits are listed below!

Water-Methanol Injection Pumps Water-Methanol Fluid Water-Methanol Nozzles/Dual Nozzle Upgrades

Although similar looking performance pumps exist they are not manufactured the same internally. The Snow Performance 300 PSI UHO methanol injection pumps come with a handful of proprietary features that puts them in a league of their own.

Dual Inlet & Outlet EPDM Seals For Safer Pressure

300 PSI For The Highest Atomization Possible

Constant Pressure, No Pulsating

Improved Heat Dissipation Flange For Cooler Running Methanol Pumps That Use Less Current

Sealed & Potted Options For 100% Weather Resistance (No Need For Rubber Sleeve That Can Retain Moisture Around Pump)


Boost Juice Baby! Snow Performance's proprietary blend of 50% distilled water 50% high quality methanol will ensure your ratios are 100% accurate for reliable safe power! This water-methanol injection fluid is sold in a case of 4 gallons designed for use in all Snow Performance water-meth injection systems.

Nitro Booster water-methanol fluid is Snow Performance's proprietary blend of nitro methane/emulsifier. When mixed into the water-methanol mixture and injected using a Snow Performance water-meth kit it can add a additional 50 HP! ONLY FOR GAS VEHICLES! 1 8oz bottle for 2qts 50/50 water/meth solution.


 
Water-Methanol Fittings/Solenoids Water-Methanol Injection Plates/Nozzle Mounting Water-Methanol Direct Port Upgrades


All Snow Performance fittings, nozzles, and water-methanol solenoids are constructed out of 100% methanol resistant stainless steel/nickel plated brass for increased reliability and quality. These fittings will work with any water-meth kit using 1/4" line and come equipped with dual EPDM methanol resistant seals for a strong leak free connection.






Snow Performance has many options to mount your water-meth nozzles. Our proprietary nozzle mount adapter lets you install a nozzle in any rubber silicon boot. Our throttle body plates make nozzle installation a breeze on virtually any application without the need to drill/tap the intake tube! For applications with metal intake tubes weldable bungs are available that are pre-threaded 1/8" NPT for a clean install. For carbureted applications a 1" carburetor spacer plate with (2) 1/8" NPT ports is availible to mount the nozzles directly underneath the carburetor. If a custom mounting solution is desired, Injection plates, throttle body, or carburetor spacer plates, are available for certain applications! Our injection & throttle spacer plates come with (2) pre drilled/tapped 1/8" NPT ports to thread the nozzle in between the throttle body and intake manifold.





An increasingly popular installation is the direct port water-methanol injection set up. This way each individual combustion chamber/intake runner gets its own dedicated water-meth nozzle for when exact amounts of water-meth are needed to each cylinder. Snow Performance has distribution blocks/kits for 4, 6, and 8 cylinder engines. All direct port methanol injection kits come with necessary tubing, distribution blocks, fittings, solenoids, and nozzle holder/check valves to convert to a direct port set up. NOTE: Nozzles are not included in our direct port injection kits and must be purchased separately.


Water-Methanol Tubing/Braided Line

The line that transports your water-methanol mixture is extremely important. Snow Performance High Temp Nylon Tubing has a 800 PSI burst rating and a temperature rating that exceeds engine bay conditions. Meaning all of our tubing, including our 1/4" nylon tubing, will not shrink or deform in hot engine bay temperatures, giving you maximum performance and safety. A must for any water-methanol injection application. Our silicone boost hoses are available in three colors (red, black, or blue).